AD5260BRUZ50
Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 5431 PCS
- Package
- TSSOP-14
- Series
- Acquisição de dados - Potenciômetros Digitais
Esta comparação detalhada entre AD5260BRUZ50 e AD5260BRUZ20 fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.
Replacement verdict
The AD5260BRUZ20 and AD5260BRUZ50 share the same 1-channel digital potentiometer architecture, TSSOP-14 package, SPI-compatible interface, and 256-position resolution, making them functionally interchangeable in most designs. The primary distinction is the end-to-end resistance of 20 kΩ versus 50 kΩ, which directly affects the current through the wiper and the resulting voltage division ratio. Designers must verify that the surrounding circuit tolerances, load impedance, and power dissipation remain within specification when substituting one resistance value for the other.
Analog Devices Inc.
Analog Devices Inc.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | AD5260BRUZ20 | AD5260BRUZ50 | Why it matters |
|---|---|---|---|
| End-to-End Resistance | 20 kΩ | 50 kΩ | Sets the nominal resistance range of the digital potentiometer and directly affects the current through and voltage across the device in a given circuit. |
| Number of Positions | 256 | 256 | Determines the resolution or number of discrete wiper settings available for adjustment. |
| Number of Taps | 256 | 256 | Defines the number of selectable resistance steps between terminal A and terminal B. |
| Interface Type | SPI | SPI | Specifies the digital communication protocol used to control the wiper position, affecting compatibility with host controllers. |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | Determines the allowable power supply voltage for proper operation and logic-level compatibility. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Indicates the environmental conditions under which the device is guaranteed to function within specification. |
| Package / Mounting Type | 14-TSSOP / Surface Mount | 14-TSSOP / Surface Mount | Ensures physical and PCB footprint compatibility for drop-in replacement. |
| Resistance Tolerance | ±30 % | ±30 % | Specifies the allowable deviation of the actual end-to-end resistance from the nominal value, impacting circuit accuracy. |
| Wiper Resistance | 60 Ω typ | 60 Ω typ | Represents the parasitic resistance of the internal switch at the wiper, affecting the minimum achievable resistance and signal integrity. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | AD5260BRUZ50 | AD5260BRUZ20 |
|---|---|---|
| Part Status | Active | Active |
| Taper | Linear | Linear |
| Configuration | Potentiometer | Potentiometer |
| Number of Circuits | 1 | 1 |
| Number of Taps | 256 | 256 |
| Resistance(Ohms) | 50k | 20k |
| Interface | SPI | SPI |
| Memory Type | Volatile | Volatile |
| Voltage - Supply | 4.5V ~ 16.5V, ±5V | 4.5V ~ 16.5V, ±5V |
| Features | Cascade Pin | Cascade Pin |
| Tolerance | ±30% | ±30% |
| Temperature Coefficient(Typ) | 35ppm/°C | 35ppm/°C |
| Mounting Type | Surface Mount | Surface Mount |
| Operating Temperature | -40°C ~ 85°C | -40°C ~ 85°C |
The primary difference is the end-to-end resistance value of the digital potentiometer. The AD5260BRUZ20 has a 20 kΩ nominal resistance, while the AD5260BRUZ50 has a 50 kΩ nominal resistance. Both are single-channel, 256-position, SPI-compatible digital potentiometers from Analog Devices in a 14-lead TSSOP package.
Yes. Both devices are offered in the same 14-lead TSSOP (RU-14) package and share the same pinout. The only difference is the internal resistor array value, so they are pin-to-pin compatible in PCB layout terms.
Not without verifying the circuit. Because the end-to-end resistance differs (20 kΩ vs 50 kΩ), the wiper resistance, power dissipation, and the resulting voltage or current in the target application will differ. The replacement is only valid if the design tolerates the new resistance value and all associated performance parameters are revalidated.
Both devices provide 256 positions (8-bit resolution) with a nominal end-to-end resistance of 20 kΩ or 50 kΩ depending on the model. They are single-channel digital potentiometers with an SPI-compatible serial interface.
Yes. Both devices operate from a single supply of 2.7 V to 5.5 V, or from dual supplies of ±2.5 V to ±2.75 V, as specified in the Analog Devices AD5260 datasheet. The supply range is independent of the resistance option.
The datasheet specifies a typical wiper resistance of 60 Ω for both the 20 kΩ and 50 kΩ versions. Wiper resistance is a function of the internal switch architecture and is not scaled with the end-to-end resistance.
Applications requiring lower absolute resistance for higher current handling or lower thermal noise, such as certain gain-setting or offset-trim circuits, may favor the 20 kΩ version. The 50 kΩ version is often chosen when lower power dissipation or higher impedance loading is desired. Selection must be based on the specific circuit requirements and verified against the datasheet.
Yes. The "Z" suffix in both part numbers indicates a RoHS-compliant, lead-free package as defined by Analog Devices. Both devices are supplied in a 14-lead TSSOP package that meets RoHS requirements.