ADM485EARZ
Analog Devices Inc.
- Lifecycle
- Active
- Stock
- 3013 PCS
- Package
- SOIC-8
- Series
- Interface - Condutores, Receptores, Transceivers
Esta comparação detalhada entre ADM485EARZ e ADM4851AR fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.
Replacement verdict
The ADM485EARZ and ADM4851AR are both half-duplex RS-485/RS-422 transceivers in 8-lead SOIC packages with 5 V supply and similar data rates, making the ADM4851AR a viable functional replacement candidate for the ADM485EARZ in many designs. However, the ADM4851AR offers a reduced driver output swing and lower differential output voltage, so the designer must validate bus-level compatibility, fail-safe behavior, and ESD/transient robustness against the specific network requirements before substituting.
Analog Devices Inc.
Analog Devices Inc.
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADM485EARZ | ADM4851AR | Why it matters |
|---|---|---|---|
| Data Rate | 2.5 Mbps | 500 kbps | Determines the maximum communication speed the transceiver can support; a faster part may be required for high-throughput buses. |
| Duplex Mode | Half-duplex | Half-duplex | Defines whether the device can transmit and receive simultaneously; both are half-duplex, so bus topology compatibility is preserved. |
| Number of Drivers/Receivers | 1/1 | 1/1 | Indicates the transceiver channel count; matching counts ensures the same bus node configuration can be used. |
| Supply Voltage | 5 V | 5 V | The operating supply voltage must match the system rail; both operate from a 5 V supply, simplifying substitution. |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | Defines the environmental range over which the device is guaranteed to operate; matching ranges ensure equivalent ruggedness. |
| Mounting Type / Package | Surface Mount, 8-SOIC | Surface Mount, 8-SOIC | Package and mounting must match the PCB footprint for a drop-in replacement. |
| ESD Protection (Bus Pins) | ±15 kV (HBM) | ±15 kV (HBM) | Higher ESD ratings improve robustness in harsh industrial environments; matching ratings indicate equivalent protection. |
| Fail-Safe Receiver | Yes (open/short circuit) | Yes (open/short circuit) | Fail-safe receivers guarantee a defined logic level when the bus is idle or faulted, preventing indeterminate states. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADM485EARZ | ADM4851AR |
|---|---|---|
| Supplier | - | Rochester Electronics, LLC |
| Part Status | Active | Obsolete |
| Type | Transceiver | Transceiver |
| Protocol | RS422, RS485 | RS422, RS485 |
| Number of Drivers/Receivers | 1/1 | 1/1 |
| Voltage - Supply | 4.75V ~ 5.25V | 4.75V ~ 5.25V |
| Mounting Type | Surface Mount | Surface Mount |
| Duplex | Half | - |
| Receiver Hysteresis | 70 mV | - |
| Data Rate | 2.5Mbps | - |
| Operating Temperature | -40°C ~ 85°C | - |
The ADM485EARZ is a 5 V, low-power, half-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package, specified for data rates up to 2.5 Mbps. The ADM4851AR is a 5 V, half-duplex RS-485/RS-422 transceiver in an 8-lead SOIC package with a higher maximum data rate of 20 Mbps and a reduced unit-load receiver input impedance of 1/8 (allowing up to 256 nodes on the bus). Both are manufactured by Analog Devices.
Yes. Both devices are offered in the same 8-lead SOIC (R-8) package with the same pinout: RO, RE, DE, DI, GND, A, B, and VCC. This allows them to share a common PCB footprint, although electrical differences must still be validated for the target design.
The ADM485EARZ supports data rates up to 2.5 Mbps. The ADM4851AR supports data rates up to 20 Mbps. The higher rate of the ADM4851AR makes it suitable for faster bus applications, while the ADM485EARZ is adequate for lower-speed networks.
The ADM485EARZ uses a standard 1-unit-load receiver input impedance, supporting up to 32 nodes on a bus. The ADM4851AR uses a 1/8-unit-load receiver input impedance, supporting up to 256 nodes on a bus. This makes the ADM4851AR preferable for large multi-drop networks.
Yes. Both the ADM485EARZ and the ADM4851AR are specified for operation from a single 5 V ±5% supply (4.75 V to 5.25 V), consistent with their datasheet specifications.
The ADM485EARZ includes enhanced ESD protection on the RS-485 bus pins, rated to ±15 kV for the human body model (HBM) and ±8 kV for the IEC 61000-4-2 contact discharge, per the Analog Devices datasheet. The ADM4851AR datasheet specifies ESD protection on the bus pins as well; designers should consult the respective datasheet for the exact verified ratings before finalizing protection requirements.
Because both devices share the same 8-lead SOIC package and pinout and operate from a 5 V supply, the ADM4851AR can be considered a candidate replacement. However, the higher 20 Mbps data rate, 1/8-unit-load input impedance, and any differences in ESD ratings, slew rate, and fail-safe behavior must be validated against the target design and the manufacturer datasheets before substitution.