ADS1231IDR
Texas Instruments
- Lifecycle
- Active
- Stock
- 4314 PCS
- Package
- SOIC-16
- Series
- Acquisição de dados - Analogo para Convertedores Digitais (ADC)
Esta comparação detalhada entre ADS1231IDR e ADS1286UCG4 fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.
Replacement verdict
The ADS1231IDR and ADS1286UCG4 are not drop-in replacements for one another. The ADS1231IDR is a 24-bit low-noise bridge sensor ADC with an integrated PGA and on-chip oscillator, while the ADS1286UCG4 is a 12-bit successive-approximation ADC with a differential input and serial interface. They differ in resolution, architecture, input configuration, and package, so a direct substitution is not feasible without redesign.
Texas Instruments
Texas Instruments
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADS1231IDR | ADS1286UCG4 | Why it matters |
|---|---|---|---|
| Resolution (bits) | 24 | 12 | Resolution determines the smallest signal change the ADC can distinguish; a 24-bit device offers far finer measurement granularity than a 12-bit device. |
| Number of input channels | 1 (differential) | 1 (differential) | Both are single-channel differential devices, so channel count is not a differentiator for substitutability. |
| Interface type | Serial (SPI-compatible, 2-wire) | Serial (SPI-compatible) | The digital interface must match the host controller; both use serial interfaces but with differing protocol details that affect firmware compatibility. |
| Supply voltage (analog) | 2.7 V to 5.3 V | 4.5 V to 5.5 V | The analog supply range determines compatibility with the system power rail; the ADS1231 supports lower-voltage rails than the ADS1286. |
| Input type / architecture | Delta-sigma with integrated PGA | SAR (successive approximation) | Delta-sigma converters excel at low-speed high-resolution measurements, while SAR converters offer faster sampling; architecture affects noise, speed, and application fit. |
| Data rate / sampling rate | 10 SPS or 80 SPS (selectable) | Up to 20 kSPS | Sampling rate determines how fast the system can capture changing signals; the SAR device is far faster while the delta-sigma device targets slow precision measurements. |
| Package type | SOIC-8 (8-pin) | VSSOP-8 / MSOP-8 | Package footprint and pinout must match the PCB layout for a drop-in replacement; differing packages require layout changes. |
| Operating temperature range | -40 °C to +85 °C | -40 °C to +85 °C | Both cover the industrial temperature range, so environmental compatibility is equivalent. |
| Integrated PGA / gain stage | Yes (gain 128) | No | An integrated PGA allows direct connection of low-level sensors without external amplification, simplifying the signal chain for the ADS1231. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADS1231IDR | ADS1286UCG4 |
|---|---|---|
| Supplier | - | Texas Instruments |
| Part Status | Active | Discontinued at Digi-Key |
| Number of Bits | 24 | 12 |
| Sampling Rate(Per Second) | 80 | 20k |
| Number of Inputs | 1 | 1 |
| Input Type | Differential | Differential |
| Data Interface | SPI | SPI |
| Configuration | ADC | S/H-ADC |
| Ratio - S / H: ADC | - | 1:1 |
| Number of A/D Converters | 1 | 1 |
| Architecture | Sigma-Delta | SAR |
| Reference Type | External | External |
| Voltage - Supply, Analog | 3V ~ 5.3V | 5V |
| Voltage - Supply, Digital | 3V ~ 5.3V | 5V |
| Operating Temperature | -40°C ~ 85°C | -40°C ~ 85°C |
The ADS1231IDR is a 24-bit delta-sigma analog-to-digital converter with an integrated low-noise programmable gain amplifier (PGA) and a bridge excitation voltage, designed primarily for weigh-scale and strain-gauge applications. The ADS1286UCG4 is a 12-bit successive-approximation-register (SAR) ADC with a pseudo-differential input and an SPI-compatible serial interface, intended for general-purpose medium-speed data acquisition. They differ fundamentally in resolution architecture (delta-sigma vs SAR), resolution (24-bit vs 12-bit), and integration level.
No. The ADS1231IDR is supplied in an 8-pin SOIC (D) package, while the ADS1286UCG4 is supplied in a 10-pin VSSOP (DGS) package. The pin counts, pin functions, and package footprints differ, so they are not drop-in replacements and require different PCB land patterns.
The ADS1231IDR operates from a single analog supply (AVDD) of 2.7 V to 5.3 V and a digital supply (DVDD) of 2.7 V to 5.3 V. The ADS1286UCG4 operates from a single supply of 2.7 V to 5.25 V. Both are low-voltage single-supply devices, but the exact specified ranges differ slightly and should be verified against the respective datasheets.
The ADS1231IDR provides a fully differential input with an integrated PGA (gain of 128) and a dedicated bridge excitation output, and it uses a simple two-wire serial interface for data readout. The ADS1286UCG4 provides a pseudo-differential input without an integrated PGA and uses a standard SPI-compatible serial interface (CS, SCLK, DOUT). The ADS1231IDR is optimized for direct sensor connection, whereas the ADS1286UCG4 requires external signal conditioning for low-level sensors.
The ADS1231IDR is specifically designed for weigh-scale and strain-gauge applications because it integrates a low-noise PGA, a 24-bit delta-sigma modulator, and a bridge excitation voltage source in a single package. The ADS1286UCG4, being a 12-bit SAR ADC without an integrated PGA or excitation source, would require external amplification and excitation circuitry and would provide lower resolution, making it less suitable for high-precision bridge sensor applications.
The ADS1231IDR provides a selectable output data rate of 10 SPS or 80 SPS. The ADS1286UCG4 is a SAR converter whose throughput is determined by the external serial clock; its maximum sampling rate is specified in its datasheet (typically up to 200 kSPS depending on SCLK). The ADS1231IDR is therefore intended for low-speed, high-resolution measurements, while the ADS1286UCG4 supports much higher sample rates at lower resolution.
No. Because they differ in resolution architecture (24-bit delta-sigma vs 12-bit SAR), package (8-pin SOIC vs 10-pin VSSOP), interface protocol, input configuration, and integration level (integrated PGA and excitation vs none), they cannot be used interchangeably without a complete redesign of the analog front end, PCB layout, and firmware.