ADS1241E
Texas Instruments
- Lifecycle
- Active
- Stock
- 1322 PCS
- Package
- SSOP-28
- Series
- Acquisição de dados - Analogo para Convertedores Digitais (ADC)
Esta comparação detalhada entre ADS1241E e ADS1286UB/2K5 fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.
Replacement verdict
The ADS1241E and ADS1286UB/2K5 are not functionally interchangeable. The ADS1241E is a multi-channel 24-bit delta-sigma ADC with an SPI interface and on-chip PGA, while the ADS1286UB/2K5 is a single-channel 12-bit successive-approximation ADC with a different digital interface and package. Designers must redesign the signal chain, interface, and board layout rather than substitute one part for the other.
Texas Instruments
Texas Instruments
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADS1241E | ADS1286UB/2K5 | Why it matters |
|---|---|---|---|
| Resolution (bits) | 24 | 12 | Resolution determines the smallest signal change the ADC can distinguish; a 24-bit ADC offers far finer measurement granularity than a 12-bit device. |
| Number of input channels | 8 (differential/ single-ended) | 1 (differential) | Channel count defines how many signals can be measured; the ADS1241E supports multi-channel systems while the ADS1286UB handles a single differential input. |
| Interface type | SPI | SPI | Both use SPI, so the host microcontroller interface is compatible, but the command protocol and register set differ significantly. |
| Supply voltage (analog) | 2.7 V to 5.25 V | 4.5 V to 5.5 V | The wider supply range of the ADS1241E allows operation from lower-voltage rails, while the ADS1286UB requires a nominal 5 V supply. |
| Package type | SSOP-28 | SOIC-8 | Package footprint and pin count affect PCB layout and board space; the two parts are not drop-in compatible. |
| Internal PGA | Yes (gain 1 to 128) | No | An integrated programmable gain amplifier allows direct connection of low-level sensors without external amplification, simplifying the signal chain. |
| Data rate (max) | 15 SPS (at 24-bit) | 20 kSPS | Maximum throughput determines suitability for fast vs. high-precision applications; the ADS1286UB samples much faster but at lower resolution. |
| Operating temperature range | -40 °C to +85 °C | -40 °C to +85 °C | Both cover the industrial temperature range, so environmental robustness is comparable for typical applications. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADS1241E | ADS1286UB/2K5 |
|---|---|---|
| Supplier | - | Texas Instruments |
| Part Status | Active | Obsolete |
| Number of Bits | 24 | 12 |
| Sampling Rate(Per Second) | 15 | 20k |
| Number of Inputs | 8 | 1 |
| Input Type | Differential, Single Ended | Differential |
| Data Interface | SPI | SPI |
| Configuration | MUX-PGA-ADC | S/H-ADC |
| Ratio - S / H: ADC | - | 1:1 |
| Number of A/D Converters | 1 | 1 |
| Architecture | Sigma-Delta | SAR |
| Reference Type | External | External |
| Voltage - Supply, Analog | 2.7V ~ 3.3V, 5V | 5V |
| Voltage - Supply, Digital | 2.7V ~ 5.25V | 5V |
| Operating Temperature | -40°C ~ 85°C | -40°C ~ 85°C |
| Features | PGA | - |
The ADS1241E is a 24-bit delta-sigma analog-to-digital converter with a built-in programmable gain amplifier (PGA) and a multiplexer, designed for multi-channel, low-frequency measurement applications. The ADS1286UB/2K5 is a 12-bit successive-approximation register (SAR) ADC with a pseudo-differential input, intended for faster, single-channel data acquisition. They differ fundamentally in resolution, architecture, input configuration, and channel count.
No. The ADS1241E is supplied in a 28-pin SSOP package, while the ADS1286UB/2K5 is supplied in an 8-pin SOIC package. The pin counts, pin functions, and PCB land patterns are not interchangeable, so a direct drop-in replacement is not possible.
The ADS1241E provides programmable output data rates typically ranging from 15 SPS to 1 kSPS depending on configuration, optimized for precision low-frequency measurements. The ADS1286UB/2K5 is a SAR converter capable of sampling rates up to approximately 200 kSPS, making it suitable for higher-speed single-channel acquisition. The two devices target different speed-versus-resolution trade-offs.
The ADS1241E includes an input multiplexer supporting multiple differential or single-ended input channels with a programmable gain amplifier, allowing direct interfacing with low-level sensors. The ADS1286UB/2K5 provides a single pseudo-differential input pair without an integrated PGA or multiplexer, so external signal conditioning is typically required for low-level signals.
Both devices support a single 5 V analog supply in their standard configurations, but their digital interface and reference requirements differ. The ADS1241E includes an on-chip PGA and multiplexer that affect supply and reference budgeting, while the ADS1286UB/2K5 requires an external reference and has a simpler supply arrangement. Designers should verify supply, reference, and digital I/O levels against the respective datasheets before sharing a rail.
The ADS1241E is better suited for multi-channel sensor measurement because it integrates an input multiplexer and a programmable gain amplifier, enabling multiple low-level differential inputs to be digitized with high 24-bit resolution. The ADS1286UB/2K5, with a single pseudo-differential input and 12-bit resolution, is better suited to single-channel, higher-speed acquisition where external multiplexing and gain stages would be added separately.
No. The two devices differ in resolution (24-bit versus 12-bit), architecture (delta-sigma versus SAR), package (28-pin SSOP versus 8-pin SOIC), channel count, input configuration, and data rate. They are not pin-compatible or functionally equivalent, so substitution requires a redesign of the analog front end, PCB layout, and firmware, validated against the respective manufacturer datasheets.