AMC1301DWVR
Texas Instruments
- Lifecycle
- Active
- Stock
- 6629 PCS
- Series
- Linear - Amplificadores - Instrumentação, OP Amps, Buffer Amps
Esta comparação detalhada entre AMC1301DWVR e AMC1305M25DWR fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.
Replacement verdict
The AMC1305M25DWR and AMC1301DWVR are both isolated delta-sigma modulator amplifiers from Texas Instruments sharing a 16-pin SOIC-wide package and a nominal 5 V supply, but they differ in input structure, isolation rating, and output interface. The AMC1305M25DWR is a single-channel modulator with a ±250 mV differential input and CMOS output, while the AMC1301DWVR is a single-channel isolated amplifier with a ±250 mV input and differential analog output. Designers should validate the output interface, isolation working voltage, and clocking requirements before substituting one for the other in a given signal chain.
Texas Instruments
Texas Instruments
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | AMC1305M25DWR | AMC1301DWVR | Why it matters |
|---|---|---|---|
| Input Type | Current shunt (isolated delta-sigma modulator) | Voltage (isolated amplifier) | Determines whether the device measures current via a shunt or amplifies a voltage signal; these are fundamentally different signal-chain functions and are not directly substitutable. |
| Output Format | 1-bit digital bitstream (delta-sigma) | Analog differential voltage | A digital bitstream requires a digital filter/decoder on the controller side, while an analog output feeds an ADC; the downstream interface architecture differs completely. |
| Isolation Rating | 5000 V RMS (reinforced) | 3000 V RMS (basic) | Higher isolation rating allows use in higher-voltage or reinforced-insulation applications; substituting a lower-rated part may violate safety requirements. |
| Input Voltage Range | ±250 mV (shunt input) | ±250 mV (with ±320 mV linear range) | Both target small shunt signals, but the usable linear input window and overload behavior differ, affecting measurement accuracy and fault tolerance. |
| Supply Voltage | 3.3 V (high side) / 3.3 V or 5 V (low side) | 5 V (high side) / 3.3 V or 5 V (low side) | High-side supply requirements differ, so the isolated power supply design must match the chosen device. |
| Gain | Fixed (modulator, no analog gain stage) | Fixed gain of 8 | The analog amplifier provides a defined gain of 8, whereas the modulator encodes the signal digitally; scaling and signal conditioning differ. |
| Bandwidth | Up to ~20 MHz clock, signal bandwidth set by digital filter | ~100 kHz (typical) | The modulator supports much higher effective bandwidth when paired with a fast digital filter, while the amplifier bandwidth is fixed, affecting control-loop speed. |
| Package | SOIC-16 (wide body) | SOIC-8 (wide body) | Different pin count and footprint prevent drop-in board replacement without layout changes. |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +105 °C | The wider temperature range of the modulator suits harsher environments; the amplifier has a lower upper limit, affecting thermal margin. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | AMC1301DWVR | AMC1305M25DWR |
|---|---|---|
| Part Status | Active | Active |
| Amplifier Type | Isolation | - |
| Number of Circuits | 1 | - |
| Gain Bandwidth Product | 1 MHz | - |
| Current - Input Bias | 60 µA | - |
| Voltage - Input Offset | 50 µV | - |
| Supply Current | 5.9mA | - |
| Current - Output / Channel | 13 mA | - |
| Voltage - Supply Span(Min) | 3 V | - |
| Voltage - Supply Span(Max) | 5.5 V | - |
| Operating Temperature | -40°C ~ 125°C | -40°C ~ 125°C |
| Mounting Type | Surface Mount | Surface Mount |
| Type | - | Isolated Module |
| Number of Channels | - | 1 |
| Resolution(Bits) | - | 16 b |
| Sampling Rate(Per Second) | - | 78k |
| Data Interface | - | CMOS, Serial |
| Voltage Supply Source | - | Analog and Digital |
| Voltage - Supply | - | 3V ~ 5.5V |
The AMC1305M25DWR is a reinforced isolated delta-sigma modulator with a ±250 mV input range and a 20 MHz clock, designed for shunt-based current sensing with a bit-stream output. The AMC1301DWVR is a precision isolated amplifier with a ±250 mV input range and a fixed gain of 8.2, providing a differential analog output. The modulator outputs a 1-bit data stream, while the amplifier outputs an analog voltage, so they serve different signal-chain architectures.
No. Both devices are offered in a 16-pin SOIC (DW) package, but their pin functions differ: the AMC1305M25DWR provides a clock input and a single-bit modulator data output, whereas the AMC1301DWVR provides a differential analog output with fixed gain. The pinouts are not interchangeable, and PCB layouts must be designed for the specific device.
Both devices are reinforced isolated components rated for 5 kV RMS isolation per UL 1577 and provide a working voltage of 1.5 kV peak per VDE V 0884-10 (VDE 0884-10). They are intended for galvanically isolated current and voltage sensing in high-voltage systems.
Both devices are specified for a linear input range of ±250 mV, making them suitable for shunt-resistor-based current sensing where the shunt voltage is small. The AMC1305M25DWR digitizes this input with a delta-sigma modulator, while the AMC1301DWVR amplifies it with a fixed gain of 8.2 to produce a differential analog output.
The AMC1305M25DWR is the appropriate choice when the system includes a digital filter (such as an FPGA or a sigma-delta modulator filter) because it outputs a 1-bit delta-sigma bit stream at a 20 MHz clock rate. The AMC1301DWVR outputs an analog signal and would require an external ADC, so it is better suited to designs that already have an analog-to-digital conversion stage.
Both devices use a 5 V analog supply on the high-voltage side and a 3.3 V or 5 V supply on the low-voltage side, depending on the specific variant and configuration. Designers should confirm the exact supply rails and decoupling requirements from the respective datasheets, as the low-side supply options and output interface differ between the modulator and the amplifier.
No. The AMC1305M25DWR produces a digital bit-stream output requiring a digital filter, while the AMC1301DWVR produces an analog output requiring an ADC. Because the output interfaces, pin functions, and signal-chain requirements differ, a direct replacement is not possible without redesigning the receiving circuitry and PCB layout.