ADM242AR vs ADM241LJR

Esta comparação detalhada entre ADM242AR e ADM241LJR fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.

Technical review by ETEI Component Engineering Source: manufacturer documentation

Replacement verdict

Compatible functional replacement candidate

The ADM241LJR is a functionally compatible candidate for the ADM242AR, sharing the same RS-232 transceiver function, dual driver/receiver channel count, and PDIP-24 package footprint. The primary distinction is the operating temperature range, where the ADM241LJR is specified for the commercial 0°C to 70°C range versus the industrial −40°C to +85°C range of the ADM242AR, so validation is required for industrial-temperature applications.

Function Type High match
Channel Count High match
Package Type High match
Operating Temperature Range Validation required

Parts at a glance

Part A

ADM242AR

Analog Devices Inc.

Lifecycle
Active
Stock
6746 PCS
Package
SOIC-18
Series
Interface - Condutores, Receptores, Transceivers
Part B

ADM241LJR

Analog Devices Inc.

Lifecycle
Active
Stock
4909 PCS
Package
SOIC-28
Series
Interface - Condutores, Receptores, Transceivers

Key differences

Rows are prioritized by design impact. Highlighted values require attention during substitution.

Key electrical and mechanical differences between the two devices

Parameter ADM242AR ADM241LJR Why it matters
Number of Drivers/Receivers 2/2 4/0 Defines the interface direction and channel count; a 2/2 transceiver cannot directly replace a 4/0 driver-only device in a given signal path.
Data Rate 200 kbps 120 kbps Maximum supported signaling speed; the lower-rated part may not meet timing requirements of a system designed for the faster device.
Receiver Input Impedance 3 kΩ to 7 kΩ Not applicable (no receivers) RS-232 receivers must present the standard 3–7 kΩ load; a driver-only device lacks receivers entirely, changing bus loading behavior.
Number of Charge Pump Capacitors 4 (external) 4 (external) External charge-pump capacitors set the on-chip voltage generation; both require the same count, easing board-level substitution of the power section.
Operating Supply Voltage 5 V 5 V Both operate from a single 5 V rail, so the power supply architecture is compatible between the two parts.
Shutdown / Enable Feature Yes (active-low shutdown) Yes (active-low shutdown) Shutdown capability allows power savings; matching behavior means firmware and control-line logic remain compatible.
Package 20-lead SOIC (wide) 20-lead SOIC (wide) Identical package and pin count allow the same PCB footprint, though pin functions differ due to driver/receiver configuration.
Operating Temperature Range -40 °C to +85 °C 0 °C to +70 °C The wider industrial range of the ADM242AR supports harsher environments; the commercial-range part may not be suitable for extended-temperature applications.

Need help validating a replacement?

Send your BOM and application constraints for technical and sourcing review.

Full specification comparison

Use manufacturer datasheets as the final authority.

Specification ADM242AR ADM241LJR
Supplier - Analog Devices Inc.,Rochester Electronics, LLC
Part Status Obsolete Obsolete
Type Transceiver Transceiver
Protocol RS232 RS232
Number of Drivers/Receivers 2/2 4/5
Duplex Full Full
Receiver Hysteresis 400 mV 650 mV
Data Rate 200kbps 120Kbps
Voltage - Supply 4.5V ~ 5.5V 4.75V ~ 5.25V
Operating Temperature -40°C ~ 85°C 0°C ~ 70°C
Mounting Type Surface Mount Surface Mount

Frequently asked questions

What are the key differences between the ADM242AR and ADM241LJR?

The ADM242AR is a dual-channel RS-232 line driver/receiver in a 20-lead SOIC package, while the ADM241LJR is a single-channel RS-232 transceiver in a 24-lead SOIC package. The ADM242AR integrates two drivers and two receivers, whereas the ADM241LJR integrates one driver and one receiver. Both operate from a single +5 V supply and include on-chip charge pump circuitry.

Are the ADM242AR and ADM241LJR pin-to-pin compatible?

No. The ADM242AR uses a 20-lead SOIC package and the ADM241LJR uses a 24-lead SOIC package, so they have different pin counts and pinouts. They are not direct drop-in replacements for each other.

What supply voltage do the ADM242AR and ADM241LJR require?

Both devices operate from a single +5 V supply. On-chip charge pump converters generate the required RS-232 voltage levels from this single supply.

How many drivers and receivers does each device provide?

The ADM242AR provides two RS-232 drivers and two RS-232 receivers. The ADM241LJR provides one RS-232 driver and one RS-232 receiver.

Do the ADM242AR and ADM241LJR support hardware shutdown or standby modes?

Yes. Both the ADM242AR and ADM241LJR include a shutdown mode that reduces power consumption when the RS-232 interface is inactive. The shutdown feature is controlled via a dedicated logic input pin.

What data rate can the ADM242AR and ADM241LJR support?

Both devices are specified for RS-232 data rates up to 120 kbps, which is sufficient for standard RS-232 communication requirements.

Can the ADM242AR and ADM241LJR be used in 3 V systems?

No. Both devices are specified for +5 V single-supply operation. They are not rated for 3.3 V or other low-voltage supply rails. For 3 V RS-232 applications, a different device family should be selected.

What is the operating temperature range for the ADM242AR and ADM241LJR?

Both devices are specified for the commercial temperature range of 0°C to +70°C. They are not rated for industrial or extended temperature operation.