ADS1259IPWR
Texas Instruments
- Lifecycle
- Active
- Stock
- 6414 PCS
- Package
- TSSOP-20
- Series
- Acquisição de dados - Analogo para Convertedores Digitais (ADC)
Esta comparação detalhada entre ADS1259IPWR e ADS1203IPWRG4 fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.
Replacement verdict
The ADS1259IPWR and ADS1203IPWRG4 are not drop-in replacements for one another. The ADS1259IPWR is a 24-bit delta-sigma ADC with an SPI interface and integrated PGA, while the ADS1203IPWRG4 is a 16-bit delta-sigma modulator with a single-bit output stream. They differ in resolution, output interface, package, and functional architecture, so direct substitution is not feasible without redesign.
Texas Instruments
Texas Instruments
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | ADS1259IPWR | ADS1203IPWRG4 | Why it matters |
|---|---|---|---|
| Resolution (bits) | 24 | 16 | Higher resolution enables finer measurement of small signal changes; a 24-bit delta-sigma ADC resolves much smaller steps than a 16-bit device. |
| Architecture | Delta-Sigma (24-bit ADC) | Delta-Sigma Modulator | The ADS1259 is a complete ADC with digital filter and SPI interface, while the ADS1203 is a modulator-only device requiring external digital filtering, so they are not drop-in substitutes. |
| Output Interface | SPI (serial) | 1-bit modulator bitstream | The interface determines how the host processor reads data; SPI delivers finished conversion codes, whereas a modulator bitstream needs an external sinc filter. |
| Input Type | Differential (single channel) | Differential | Differential inputs reject common-mode noise; both are differential, but channel count and configuration differ, affecting system design. |
| Data Rate / Sample Rate | Up to 2.5 kSPS (programmable) | Up to 40 kSPS (modulator clock dependent) | Sample rate sets the achievable measurement bandwidth and noise trade-off; the modulator runs much faster but requires external decimation. |
| Supply Voltage | 5 V analog, 2.7–5.25 V digital | 5 V analog, 3.0–5.5 V digital | Supply requirements must match the board's power rails; slight differences in digital supply range can affect compatibility. |
| Package | TSSOP-20 | TSSOP-16 | Different pin counts and footprints mean the PCB layout must be redesigned; they are not footprint-compatible. |
| Internal PGA / Gain | Yes (programmable gain) | No (fixed gain via external front end) | An internal PGA allows direct connection of low-level sensors; without it, external amplification is required, changing the analog front-end design. |
| Typical Application | Precision industrial measurement, weigh scales | Motor control, current sensing, isolated measurement | Intended use cases differ significantly; the ADS1203 targets fast control loops, while the ADS1259 targets high-accuracy DC measurement. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | ADS1259IPWR | ADS1203IPWRG4 |
|---|---|---|
| Supplier | - | Texas Instruments |
| Part Status | Active | Obsolete |
| Type | - | Modulator |
| Number of Channels | - | 1 |
| Resolution(Bits) | - | 16 b |
| Sampling Rate(Per Second) | 14k | 40k |
| Data Interface | SPI | Serial |
| Voltage Supply Source | - | Single Supply |
| Voltage - Supply | - | 4.75V ~ 5.25V |
| Operating Temperature | -40°C ~ 105°C | -40°C ~ 125°C |
| Mounting Type | - | Surface Mount |
| Number of Bits | 24 | - |
| Number of Inputs | 1 | - |
| Input Type | Differential, Single Ended | - |
| Configuration | ADC | - |
| Number of A/D Converters | 1 | - |
| Architecture | Sigma-Delta | - |
| Reference Type | External | - |
| Voltage - Supply, Analog | 5V | - |
| Voltage - Supply, Digital | 2.7V ~ 5.25V | - |
| Features | PGA | - |
The ADS1259IPWR is a 24-bit, 14.4-kSPS delta-sigma analog-to-digital converter with an integrated low-noise programmable gain amplifier and a serial SPI interface, designed for high-resolution, low-frequency measurement applications. The ADS1203IPWRG4 is a 16-bit, 10-MHz clock delta-sigma modulator that outputs a 1-bit data stream for isolated or high-speed signal conditioning, typically paired with an external digital filter or FPGA. In short, the ADS1259 is a complete ADC with digital output, while the ADS1203 is a modulator requiring external digital filtering.
No. The ADS1259IPWR is supplied in a 20-pin TSSOP (PW) package, while the ADS1203IPWRG4 is supplied in a 16-pin TSSOP (PW) package. They differ in pin count and pin functions, so they are not drop-in replacements and require different PCB footprints and layouts.
The ADS1259IPWR provides 24-bit resolution with programmable data rates up to 14.4 kSPS. The ADS1203IPWRG4 is a 16-bit delta-sigma modulator that produces a 1-bit output stream at a clock rate up to 10 MHz, with the effective resolution determined by the external digital filter and decimation ratio.
No. The ADS1259IPWR uses a SPI-compatible serial interface for reading conversion results and configuring registers. The ADS1203IPWRG4 outputs a single-bit delta-sigma data stream plus a clock signal, and does not provide a register-based SPI interface; it requires an external digital filter or controller to process the bitstream.
The ADS1259IPWR operates from an analog supply of 5 V (with a digital supply of 2.7 V to 5.25 V) per the datasheet. The ADS1203IPWRG4 operates from a single 5 V supply for both analog and digital sections. Designers should confirm exact supply ranges and decoupling requirements in the respective manufacturer datasheets.
The ADS1203IPWRG4 is generally preferred for isolated signal acquisition because its 1-bit delta-sigma output stream can be passed through a single digital isolator, simplifying isolation barrier design. The ADS1259IPWR, with its multi-bit SPI output, would require isolating multiple digital lines, increasing complexity and cost in isolated systems.
No. Beyond package and pin differences, the ADS1203IPWRG4 lacks the integrated digital filter, PGA, and SPI register interface of the ADS1259IPWR. A direct substitution would require adding an external digital filter and redesigning the interface and PCB layout, so it is not a drop-in replacement.