AMC1305M25DWR
Texas Instruments
- Lifecycle
- Active
- Stock
- 3118 PCS
- Package
- SOIC-16
- Series
- Acquisição de dados - ADCs-DACs - Objetivo Especial
Esta comparação detalhada entre AMC1305M25DWR e AMC1302DWV fornece informações valiosas sobre suas especificações e principais características. Abordamos fatores importantes em detalhes, incluindo conformidade com RoHS, status REACH, série, estilo de montagem, tipo de encapsulamento e outras características relevantes. Apresentar as diferenças lado a lado simplifica a seleção de componentes, facilitando a escolha da melhor opção para sua aplicação específica.
Replacement verdict
The AMC1305M25DWR and AMC1302DWV are both isolated delta-sigma modulator amplifiers, but they differ fundamentally in input architecture, isolation performance, and package footprint, so neither part can directly substitute for the other without a full circuit and layout redesign.
Texas Instruments
Texas Instruments
Rows are prioritized by design impact. Highlighted values require attention during substitution.
Key electrical and mechanical differences between the two devices
| Parameter | AMC1305M25DWR | AMC1302DWV | Why it matters |
|---|---|---|---|
| Input Type | Current shunt (isolated delta-sigma modulator for shunt resistor) | Isolated amplifier (voltage input) | The two parts measure fundamentally different signal types; one is a modulator for current sensing via a shunt, the other is an isolated amplifier for voltage sensing, so they are not functionally interchangeable. |
| Output Format | 1-bit delta-sigma bitstream (digital) | Differential analog voltage | A digital bitstream output requires an external digital filter/decoder, while an analog output feeds an ADC directly; the downstream signal chain differs completely. |
| Isolation Rating | 5000 V RMS (reinforced) | 5000 V RMS (reinforced) | Both provide reinforced isolation suitable for high-voltage sensing, so isolation capability is comparable and not a differentiator. |
| Input Voltage Range | ±250 mV (shunt input) | ±50 mV (with gain, voltage input) | The input range determines the shunt or voltage divider design; the modulator accepts a larger shunt signal while the amplifier targets small differential voltages. |
| Gain | Fixed modulator gain (bitstream density proportional to input) | Fixed gain of 41 | The amplifier provides a defined analog gain, whereas the modulator encodes the input as bitstream density; scaling behavior in the system differs. |
| Supply Voltage | 3.3 V or 5 V (high side), 3.3 V or 5 V (low side) | 3.3 V or 5 V (high side), 3.3 V or 5 V (low side) | Both support common 3.3 V and 5 V rails on either side of the isolation barrier, so supply compatibility is similar. |
| Package | SOIC-16 (wide body) | SOIC-8 (wide body) | Different package footprints and pin counts mean the PCB layout cannot be shared without redesign. |
| Operating Temperature Range | -40°C to +125°C | -40°C to +125°C | Both cover the industrial temperature range, so thermal suitability is equivalent. |
| Typical Application | Motor drive current sensing, shunt-based current measurement | Voltage sensing, isolated signal conditioning | The intended use cases differ, confirming they serve different roles in a system rather than being drop-in substitutes. |
Send your BOM and application constraints for technical and sourcing review.
Use manufacturer datasheets as the final authority.
| Specification | AMC1305M25DWR | AMC1302DWV |
|---|---|---|
| Supplier | - | Texas Instruments |
| Part Status | Active | Active |
| Type | Isolated Module | Isolation |
| Applications | - | Current Sensing, Power Management |
| Mounting Type | Surface Mount | Surface Mount |
| Number of Channels | 1 | - |
| Resolution(Bits) | 16 b | - |
| Sampling Rate(Per Second) | 78k | - |
| Data Interface | CMOS, Serial | - |
| Voltage Supply Source | Analog and Digital | - |
| Voltage - Supply | 3V ~ 5.5V | - |
| Operating Temperature | -40°C ~ 125°C | - |
The AMC1305M25DWR is a precision, isolated delta-sigma modulator with a ±250 mV input range and a 20 MHz clock, designed for direct shunt-resistor current sensing. The AMC1302DWV is an isolated amplifier with a ±50 mV input range and a fixed gain of 41, intended for shunt-based current measurement with a differential output. The modulator outputs a 1-bit data stream, while the amplifier outputs an analog differential voltage.
No. The AMC1305M25DWR is supplied in an 8-pin SOIC (DWR) package, while the AMC1302DWV is supplied in an 8-pin SOIC (DWV) package. Although both are 8-pin SOIC devices, the pin functions differ: the AMC1305M25DWR provides a modulator clock input and a 1-bit data output, whereas the AMC1302DWV provides a differential analog output and does not require an external clock. They are not direct drop-in replacements.
The AMC1305M25DWR has a specified input range of ±250 mV, suitable for shunt resistors producing a 250 mV full-scale drop. The AMC1302DWV has a specified input range of ±50 mV, making it appropriate for lower-value shunt resistors or lower current ranges. The input range difference directly affects the shunt resistor selection and the achievable measurement resolution.
Yes, both the AMC1305M25DWR and AMC1302DWV are reinforced isolated devices. Both are rated for a maximum isolation working voltage of 1500 VRMS and a transient overvoltage of 7000 VPK per the manufacturer's datasheet, and both are qualified to UL 1577 and VDE 0884-10 standards. The isolation barrier is a core feature of both parts for high-voltage current sensing applications.
The AMC1305M25DWR is the appropriate choice when a digital output is required, because it is a delta-sigma modulator that outputs a 1-bit data stream at a 20 MHz clock rate, which can be processed by an MCU or FPGA digital filter. The AMC1302DWV provides an analog differential output and would require an external ADC to interface with an MCU. The selection depends on whether the system architecture uses a digital isolator/modulator path or an analog isolation amplifier followed by an ADC.
Both devices operate from a 5 V supply on the high-side (isolated) side and a 3.3 V or 5 V supply on the low-side (controller) side, per the manufacturer datasheet. The AMC1305M25DWR requires a 5 V high-side supply and a 3.3 V or 5 V low-side supply, while the AMC1302DWV similarly uses a 5 V high-side supply and a 3.3 V or 5 V low-side supply. Designers should verify the exact recommended operating conditions in the respective datasheets for the target application.
No. Because the AMC1305M25DWR outputs a 1-bit modulator data stream and requires an external clock, while the AMC1302DWV outputs an analog differential voltage, the downstream signal chain (digital filter, ADC, or MCU interface) differs fundamentally. Additionally, the input ranges differ (±250 mV versus ±50 mV), so the shunt resistor and signal scaling would need to be recalculated. A direct replacement is not possible without redesigning the signal path and validating the new configuration.
The AMC1305M25DWR is typically used in motor drive current sensing, inverter phase current measurement, and industrial power supplies where a digital modulator output is preferred for isolation and noise immunity. The AMC1302DWV is typically used in shunt-based current sensing in motor control, solar inverters, and battery management systems where an analog isolated amplifier output is required. Both target high-voltage, isolated current-sensing applications but differ in output format and input range.